6-Wire Whip Attachment Fits KitchenAid Tilt-Head Stand Mixer Replace K45WW, Stainless Steel, Egg Heavy Cream Beater, Cakes Mayonnaise Whisk
High quality stainless steel Wire Whip aftermarket replacement for KitchenAid Tilt-Head Stand Mixer replaces part numbers of K45WW, 9704329, 4162165, 9706446, 4176070, K455 and 4169927.
Fits Models:
KitchenAid KSM15, KSM110, KSM103, KSM75, KN15, K45, and KSM90 stand mixers
Wire Whip for mixtures that need air incorporated:
eggs, sponge cakes, egg whites, angel food cakes, heavy cream, mayonnaise, boiled frostings, some candies etc.
How to Attach/Remove a wire whip
To attach Wire Whip:
1. Turn speed control to OFF.
2. Unplug Stand Mixer or disconnect power.
3. Tilt motor head back.
4. Slip beater onto beater shaft and press upward as far as possible.
5. Turn beater to right, hooking beater over pin on shaft.
6. Plug into a grounded 3 prong outlet.
To Remove Wire Whip
1. Turn speed control to OFF.
2. Unplug Stand Mixer or disconnect power.
3. Tilt motor head back.
4. Press beater upward as far as possible and turn left.
5. Pull beater from beater shaft.
How to adjust the BEATER TO BOWL CLEARANCE
If the Wire Whip hits the bottom of the bowl or is too far away from the bowl, you can correct the clearance easily
1. Turn speed control to OFF.
2. Unplug Stand Mixer or disconnect power.
3. Tilt motor head back.
4. Turn beater height adjustment screw SLIGHTLY counterclockwise (left) to raise the Wire Whip or clockwise (right) to lower the Wire Whip.
5. Make adjustment so that the Wire Whip just clears the surface of the bowl. If you over adjust the screw, you may not be able to lock the motor head when it is lowered.
Cleaning Tips:
Wire Whip should be hand washed and dried immediately. Do not wash the Wire Whip in a dishwasher. Do not store the beaters on the shaft
Package include:
1 x Wire Whip
Product Features
- ☆ 6-WIRE WHIP: quickly incorporates air into ingredients for fluffy whipped cream, perfect boiled frostings and cakes with whipped egg whites
- ☆ RUSTPROOF&BURNISHED: made of high quality durable stainless steel, which is rustproof&burnished and easy to clean
- ☆ GOOD CAPABILITY: fits KitchenAid KSM15, KSM110, KSM103, KSM75, KN15, K45, and KSM90 models stand mixers
- ☆ OEM STANDARD: built to strict quality control standards, up to OEM standard and can replace the part number of K45WW, 9704329, 4162165, 9706446, 4176070, K455 and 4169927
- ☆ GUARANTEE: 100% satisfaction customer care and money back warranty
Loading...
Works Great For Cold Smoking On My Patio With My Inexpensive DIY “Smoke House”. This smoker tube has worked perfectly for me, although so far I’ve only used with A-MAZE-N pellets. It is easy to light with a propane torch. I fill the tube, stand it on end, and hold the torch flame on the pellets for about 15 seconds to get them lighted and burning well. I leave the tube standing upright to burn for a few minutes, then blow out the flames and lay it on it’s side in the smoker. Before using it, I was wondering if the pellets would fall out when I lay on its side – but no…
I love this smoker tube so far! The square tube seems stout enough to hold up over time; obviously time will tell. The stainless steel discolored upon first use but that’s no concern to me. The important thing is that it holds pellets that produce good smoke, and this product is 100% on target. Using a propane torch to light the pellets was easy, and they lasted a good 3+ hours in this box. The pellets caught on fire once during the burn, but I quickly doused it with a small squirt of…